How To Install Golf Cart Club Protector

How To Install Golf Cart Club Protector

Keyword: How to install golf cart club protector?

LSI: golf cart rear bag cover, yamaha golf cart cabana cover, club protector elite

Introduction

A club protector is a golf cart club accessory. It is the most beneficial property of your golf cart club. The club protector elite contains a window with a downfold awning. 

It is used to protect your club and bag. It is also used to keep all of your members and clubs safe from natural disasters. 

I hope that meanwhile you are known to What is a club protector?

Are you careful with all the above aspects? I think you are serious about all of them. Then as a serious golfer do you know How to install golf cart club protector?

How To Install Golf Cart Club Protector

It is simple to attach a golf cart rear bag cover to your golf cart. Let’s start a deep dive through the tutorial below: How to install golf cart club protector?

General Information and Precautions

Read carefully the club protector kit installation instructions before you start the installation process. 

The canopy style identifies the club protector kit installation process. The canopy style is best defined by the design of the seat back. Usually, there are two seats back designs available i.e. separate - one is the driver’s seat and another for the passenger, or one-piece - only one seat available for the driver spanning the width of the golf cart.

The canopy style or the other will vary depending on the seat back design.

OBSERVE THE FOLLOWING WARNING STATEMENTS AND PROCEDURES! If you fail to do so you may be severely injured. Your property or vehicle i.e. golf cart rear bag cover may be damaged:

Warning

• YOUR VEHICLE SHOULD BE REPAIRED OR SERVICED BY ONLY SKILLED TECHNICIANS. ANYONE SHOULD HAVE EXPERIENCE WITH KNOWLEDGE WHO WANTS TO DO EVEN SIMPLE SERVICE OR REPAIR. MUST HEED ALL THE STATEMENTS OF WARNING AND FOLLOW ALL OF THE PROCEDURES CAREFULLY.

• BEFORE SERVICING TURN THE KEY SWITCH OFF, NEUTRAL THE FORWARD / REVERSE HANDLE PLACEMENT AND REMOVE THE KEY.

Tools Required

• PLIERS

• 7/16 INCH ⅜ DRIVE SOCKET

• ½ INCH ⅜ DRIVE SOCKET

• ⅜ DRIVE RATCHET

• 1-100 IN-LB TORQUE WRENCH

• ½ INCH OPEN-END WRENCH

• 7/16 INCH OPEN-END WRENCH

• 9/32 INCH DRILL BIT

• ⅜ INCH ELECTRIC HAND DRILL

• MARKER PEN

Parts In This Kit

• CLUB PROTECTOR

• TRACKING BAR

• MOUNTING BRACKET

• ¼ - 20 X 3 - ½ INCH HEX HEAD CAP SCREW

• ¼ - 20 X ½ INCH HEX HEAD CAP SCREW

• ¼ - 20 NYLON LOCK NUT

• ¼ FLAT WASHERS

• 1 INCH SPACER

1. Mount Protector onto Canopy - Separate Seat Backs

• If you have a golf cart with separate seat backs, this step is associated with your vehicle. Otherwise follow step 2.

1. Lose the nuts and remove the screws and canopy trim plates from the canopy (Figure 1).

2. Place the tracking bar between the canopy and canopy supports (Figure 2).

3. Keep the alignment of the holes in the canopy with the holes in the tracking bar. Tight the hardware to 45 in-lb (5.1 N-m) that was removed in step 1.1 (Figure 2).

2. Mount Protector onto Canopy - One-Piece Seat Back

• If you have a golf cart with a one-piece seat back, this step pertains to your vehicle.

1. Keep the two gussets against the tracking bar at the back of the canopy (Figure 4). Align the tracking bar with the canopy.

2. Use the innermost holes of the tracking as templates to mark the center of new mounting through each canopy gusset. Make two holes of 9/32 inch onto canopy gussets (Figure 4). Observe below cautiousness.

Caution

• Avoid drilling into the canopy exterior.

3. Make sure the security from the tracking bar to the canopy using ¼ locknuts, ¼ flat washers, and ¼ - 20 x ½ hex head screws as shown in Figure 5. Tight the hardware to 45 in-lb (5.1 N-m).

3. Attach The Club Protector to the Tracking Bar 

1. Slide the club protector’s beaded edge into the tracking bar’s slot as shown in Figure 6.

2. Holding the protector in place crimps both ends of the tracking bar by using pliers (Figure 6).

4. Install Mounting Bracket

1. Open screws, washers, and locknuts secure the bag hoop from the rear seat support (Figure 7). Now remove bag hoop mounting hardware.

2. Install mounting bracket to rest on the golf cart rear bag cover (Figure 8). It’s time to check the canvas. Sometimes the canvas seems tight. Add spacers as needed to raise the bracket till removing tension in the canvas.

3. Install two nylon lock nuts, and two ¼ - 20 x 3 - ½ hex head cap screws, and add spacers as required (Figure 8).

Questions

If you have further questions regarding how to install golf cart club protector then I recommend you contact your local respective distributor or dealer. 

Conclusion

Be serious, use the yamaha golf cart cabana cover. If you are a pro golfer, try the club protector elite. After completing the installation procedure properly your golf cart is ready to go. Let you enjoy your golf cart in every weather you are on the way with additional protection if required.